Electret Microphone Amplifier MAX4466 with Adjustable Gain microphone Sound sencor เซนเซอร์เสียงความไวสูง ชิฟ MAX4466

Electret Microphone Amplifier MAX4466 with Adjustable Gain microphone Sound sencor เซนเซอร์เสียงความไวสูง ชิฟ MAX4466
Electret Microphone Amplifier MAX4466 with Adjustable Gain microphone Sound sencor เซนเซอร์เสียงความไวสูง ชิฟ MAX4466Electret Microphone Amplifier MAX4466 with Adjustable Gain microphone Sound sencor เซนเซอร์เสียงความไวสูง ชิฟ MAX4466
รหัสสินค้า SKU-00563
หมวดหมู่ โมดูลเสียง
ราคา 65.00 บาท
สถานะสินค้า พร้อมส่ง
ลงสินค้า 16 ก.ย. 2565
อัพเดทล่าสุด 16 ก.ย. 2565
คงเหลือ ไม่จำกัด
จำนวน
ชิ้น
หยิบลงตะกร้า
บัตรประชาชน
บุ๊คแบ๊งค์
คุ้มครองโดย LnwPay
Electret Microphone Amplifier MAX4466 with Adjustable Gain microphone Sound sencor เซนเซอร์เสียงความไวสูง ใช้ชิฟ MAX4466

เซนเซอร์เสียง สำหรับตรวจวัดความดังเสียง ใช้ IC MAX4466 ปรับกำลังขยายได้ที่ตัวต้านทานปรับค่าได้ที่ด้านหลังโมดูล
ใช้งานง่าย จ่ายไฟ 3.3-5V ที่ขา VCC และ 0V ที่ขา GND 

ให้ค่าเอาต์พุตออกมาแบบ Analog สามารถใช้กับงานได้หลากหลาย เช่น ตรวจจับเสียงดีดนิ้ว เสียงตบมือ หรือวัดระดับความดังเสียงต่าง ๆ


ต่อวงจร Arduino Arduino สอนวิธีใช้งาน เซนเซอร์เสียงความไวสูง ใช้ชิฟ MAX4466
  • ขา VCC - 5V
  • ขา GND - GND
  • ขา OUT - A0

อัพโหลดโคดตัวอย่างนี้ แล้วดูผลลัพธ์

  // Example By ArduinoAll www.arduinoall.com
  // VCC - 3.3-5V
  // GND - GND
  // OUT - A0
  void setup() {
  Serial.begin(9600);
  Serial.println("Start Sound Detect");
  }
   
  void loop() {
  int mic = analogRead(A0);
  //Serial.println(mic); // แสดงระดับความดัง
  if (mic > 750) { // ถ้าดังเกินกว่า 750 ให้แสดงข้อความ
  Serial.println("ArduinoAll Click");
  delay(50);
  }
  }
view rawA953.ino hosted with ❤ by GitHub
---

เปิดดูผลลัพธ์ใน Serial Monitor จะเห็นเซนเซอร์เสียงอ่านค่าความดังออกมาเป็นค่าต่าง ๆ เมื่อเราปรบมือ หรือดีดนิ้ว เสียงจะดังถึงระดับที่ตั้งไว้ จะแสดงข้อความ 
ArduinoAll Click




สามารถปรับความไวของไมค์เซนเซอร์เสียง ได้ที่ด้านหลังบอร์ด ที่ตัวต้านทานปรับค่าได้






Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly as noisy or scratchy as other mic amp breakouts we've tried!
 
This breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x. That's down to be about 200mVpp (for normal speaking volume about 6" away) which is good for attaching to something that expects 'line level' input without clipping, or up to about 1Vpp, ideal for reading from a microcontroller ADC. The output is rail-to-rail so if the sounds gets loud, the output can go up to 5Vpp!
 
Using it is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply). The audio waveform will come out of the OUT pin. The output will have a DC bias of VCC/2 so when its perfectly quiet, the voltage will be a steady VCC/2 volts (it is DC coupled). If the audio equipment you're using requires AC coupled audio, place a 100uF capacitor between the output pin and the input of your device. If you're connecting to an audio amplifier that has differential inputs or includes decoupling capacitors, the 100uF cap is not required.
 
The output pin is not designed to drive speakers or anything but the smallest in-ear headphones - you'll need an audio amplifier (such as our 3.7W stereo amp) if you want to connect the amp directly to speakers. If you're connecting to a microcontroller pin, you don't need an amplifier or decoupling capacitor - connect the OUT pin directly to the microcontroller ADC pin.


ข้อมูลเพิ่มเติม

  • https://www.adafruit.com/product/1063

วิธีการชำระเงิน

ร้านค้านี้ยังไม่ได้กำหนดวิธีการชำระเงิน กรุณา ติดต่อกับทางร้าน เกี่ยวกับรายละเอียดในการชำระเงิน
ทางร้านยังไม่ได้ทำการเพิ่มบัญชีรับเงิน กรุณาติดต่อ เจ้าของร้าน

CATEGORY

MEMBER

STATISTIC

หน้าที่เข้าชม114,268 ครั้ง
ผู้ชมทั้งหมด51,030 ครั้ง
เปิดร้าน31 ก.ค. 2559
ร้านค้าอัพเดท4 ก.ย. 2568

CONTACT US

รายการสั่งซื้อของฉัน
เข้าสู่ระบบด้วย
เข้าสู่ระบบ
สมัครสมาชิก

ยังไม่มีบัญชีเทพ สร้างบัญชีใหม่ ไม่มีค่าใช้จ่าย
สมัครสมาชิก (ฟรี)
รายการสั่งซื้อของฉัน
ข้อมูลร้านค้านี้
ร้านบ้านโค้ด-Bancode
บ้านโค้ด-Bancode
จำหน่ายบอร์ดไมโครคอนโทรลเลอร์ Arduino,Module,Shield,Sensor,R,L,C,IC เเละอื่นๆ โทร.0624952525
เบอร์โทร : 0964188828
อีเมล : bancode.dev@gmail.com
ส่งข้อความติดต่อร้าน
เกี่ยวกับร้านค้านี้
สินค้าที่ดูล่าสุด
ดูสินค้าทั้งหมดในร้าน
สินค้าที่ดูล่าสุด
บันทึกเป็นร้านโปรด
Join เป็นสมาชิกร้าน
แชร์หน้านี้
แชร์หน้านี้

TOP เลื่อนขึ้นบนสุด
พูดคุย-สอบถาม